|
Product Details:
Payment & Shipping Terms:
|
The 1756-PB72 (also written 1756PB72) is the standard ControlLogix DC power supply: 18…32 V DC input, 75 W output into the chassis backplane, 10 A at 5.1 V DC and 2.8 A at 24 V DC.
It is the supply for panels that already run a 24 V DC bus — battery-backed substation cabinets, remote skids and machines where the control voltage is DC and an AC feed is not wanted.
| 1756-EN2F | CLX HI CAP EIP MOD - FBR | IN STOCK |
| 1756-EN2T | ControlLogix Hi Capacity ENET/IP | IN STOCK |
| 1756-EN2TR | 2-PORT CLX HI-CAP ENET/IP MODULE - TP | IN STOCK |
| 1756-EN2TRXT | CLX ENET/IP Module - 2TP -X Envt | IN STOCK |
| 1756-EN2TSC | EtherNet/IP Hi Prof Sngl Port VPN Bridge | IN STOCK |
| 1756-EN2TXT | CLX ENET/IP MODULE - TP, X-ENVT | IN STOCK |
| 1756-EN3TR | ControlLogix Ethernet Motion Module | IN STOCK |
| 1756-ENBT | ControlLogix Communication Module | IN STOCK |
| 1756-EWEB | ControlLogix Web Server Module | IN STOCK |
| 1756-EXT | ControlLogix Backplane Extender | IN STOCK |
| 1756-HIST1G | Historian ME 1 Gig in ControlLogix Rack | IN STOCK |
| 1756-HIST2G | Historian ME 2 Gig in ControlLogix Rack | IN STOCK |
| 1756-HSC | ControlLogix High-Speed Counter Module | IN STOCK |
| 1756-HYD02 | ControlLogix Analog Combination Module | IN STOCK |
Application |
Chassis power supply, DC input |
Brand Name |
Rockwell (Rockwell) |
Cat Num |
1756-PB72 |
Type |
ControlLogix standard power supply |
Sub Brand |
ControlLogix |
Mounting |
Left end of 1756 chassis |
Input Voltage |
18…32 V DC, nominal 24 V DC |
Input Power |
95 W maximum |
Output Power |
75 W at 0…60 °C |
Current At 5.1 V |
10 A |
Current At 24 V |
2.8 A |
Current At 3.3 V |
4 A |
Current At 1.2 V |
1.5 A |
Inrush Current |
30 A maximum |
Hold-Up |
35 ms at 18 V; 40 ms at 24 V; 40 ms at 32 V |
Isolation |
250 V reinforced, tested 3500 V DC for 60 s |
Chassis |
1756-A4, A7, A10, A13, A17; series B, C |
Wire Size |
2.5 mm² (14 AWG), 90 °C minimum |
Terminal Torque |
0.565 N·m (5 lb·in) |
Weight |
0.95 kg (2.10 lb) |
Dimensions |
14.0 x 11.2 x 14.5 cm |
Attribute values above are reproduced from the manufacturer's product data. For the authoritative technical record see Rockwell publications 1756-TD003 (module specifications) and 1756-IN050 (installation instructions). Certification details, with certificate and file numbers, are listed in the FAQ below.
The input window is 18…32 V DC, which is narrower than a 24 V bus usually looks. A battery string floating at 27 V falls towards 21 V at end of discharge and rises above 28 V on boost, so the supply sees a wide band — but a 12 V or 48 V system cannot feed it at all.
Output is 75 W total across the four rails, with the same per-rail limits as the AC unit at this power level: 1.5 A at 1.2 V, 4 A at 3.3 V, 10 A at 5.1 V and 2.8 A at 24 V. Raising the 5.1 V current is what the 13 A PB75 is for, not what a larger chassis changes.
Hold-up on DC input is specified in milliseconds rather than cycles: 35 ms at 18 V, 40 ms at 24 V and 40 ms at 32 V. A DC system usually has a battery behind the supply, so this figure describes the ride-through of the supply itself, not that of the plant.
Inrush is 30 A maximum on the DC units, higher than the 20 A of the AC units, which matters when several chassis share a battery bus and one disconnect energises all of them.
Isolation is 250 V continuous, reinforced, type tested at 3500 V DC for 60 seconds — enough to keep the field DC bus and the backplane reference separate, which is the reason a DC supply is chosen over an AC unit in a mixed cabinet.
The supply mounts at the left end of a 1756-A4, A7, A10, A13 or A17 chassis in series B or C, so a series A chassis cannot take it. Input wiring is 2.5 mm² (14 AWG) at 90 °C minimum, terminated at 0.565 N·m.
A power supply carries no diagnostic display of its own; the useful evidence is the input voltage under load, the total chassis wattage and the published hold-up at the site voltage.
| Indicator | State | Meaning and first action |
| Chassis browns out on a load step | Voltage dip | The 75 W output budget is shared by all rails; an added 24 V load can exhaust it before the 5.1 V current limit is reached. |
| Supply restarts on a short | Inrush | Inrush is 20 A on the AC unit and 30 A on the DC unit; confirm the upstream breaker tolerates repeated energisation. |
| Hold-up shorter than expected | — | Hold-up is published in cycles at a stated input and load, not as a fixed millisecond figure. |
Input, output and hold-up figures per Rockwell publication 1756-TD005-EN-E and 1756-IN050.
Check the DC bus voltage at the supply terminals while the chassis is loaded. A bus that reads 24 V open and 19 V under load is close to the bottom of the window and will look like a failing supply.
Confirm the chassis budget against 75 W total. A PB72 trips on an added 24 V load long before the 5.1 V rail reaches 10 A.
Reuse the input terminations only if they are tight and correctly gauged; a high-resistance joint on a 30 A inrush path is a common cause of intermittent restarts.
What is the 1756-PB72?
A standard ControlLogix DC power supply with a 24 V DC input and 75 W output.
What input voltage range does it accept?
18…32 V DC, nominal 24 V DC.
What current is available at 5.1 V DC?
10 A.
What is the total output power?
75 W at 0…60 °C, shared across the backplane rails.
What is the hold-up time?
35 ms at 18 V DC, 40 ms at 24 V DC and 40 ms at 32 V DC.
What is the maximum inrush current?
30 A.
Which chassis series does it fit?
1756-A4, A7, A10, A13 and A17 chassis in series B or C.
What isolation does it provide?
250 V continuous, reinforced, power input to backplane, tested at 3500 V DC for 60 s.
Data sources. Technical values on this page come from Rockwell publications 1756-TD005 (ControlLogix Power Supplies Specifications) - input, output, hold-up, isolation and environmental data for 1756-PB72; 1756-SG001 (ControlLogix System Selection Guide) - chassis and supply selection and the manufacturer's product page for 1756-PB72. Values re-checked 16 November 2026.